General Information
Vari-Speed Header set-up guide
|
CVS/RVS 18-32 |
Select Gear Input Shaft |
Select Gear Intermediate |
Auger Drive Sprocket |
Auger Finger Quantity |
PTO Yoke |
|
Case IH 16/21/23 |
47 Teeth (192592 06) |
22 Teeth (1933599 06) |
18 Teeth - 3/4"pt (192768 18) |
16 |
Hexagon PTO 00070 |
|
Case IH 8010 |
45 Teeth (192592 07) |
24 Teeth (193599 07) |
16 Teeth - 3/4"pt (192768 04) |
24 |
6 Spline PTO00080 |
|
John Deere 9600 9610 8820 |
47 Teeth (192592 06) |
22 Teeth (193599 06) |
18 Teeth - 3/4"pt (192768 18) |
24 |
Hexagon PTO00070 |
|
John Deere 9500 7720 CTS |
47 Teeth (192592 06) |
22 Teeth (193599 06) |
18 Teeth - 3/4"pt (192768 18) |
20 |
Hexagon PTO00070 |
|
John Deere STS |
47 Teeth (192592 06) |
22 Teeth (193599 06) |
18 Teeth - 3/4"pt (192768 18) |
20 |
21 Spline PTO00082 |
|
New Holland TR Models |
45 Teeth (192592 07) |
24 Teeth (193599 07) |
16 Teeth - 3/4"pt (192768 04) |
16 |
6 Spline PTO00080 |
|
Cleaner R-Series |
45 Teeth (192592 07) |
24 Teeth (193599 07) |
15 Teeth - 3/4"pt (192768 16) |
16 |
21 Spline PTO00082 |
|
CAT 480 485 |
42 Teeth (192592 01) |
27 Teeth (193599 01) |
13 Teeth - 3/4"pt (192768 08) |
24 |
21 Spline PTO00082 |
|
CAT 460 465 |
42 Teeth (192592 01) |
27 Teeth (193599 01) |
16 Teeth - 3/4"pt (192768 04) |
24 |
21 Spline PTO00082 |
Tacho Head Trouble Shooting
Powering the Monitor:
Brown Wire +
Blue Wire -
Connect Brown Wire to 12 volt KEYED power source. You can get power from constant 12v source but is recommended to be keyed. (Battery Drain)
Setting Monitor Alarm Rotor Speed:
When the machine is running at working speed not under load. Press and hold the set button till the screen displays AUTO. Release and it will calculate a 8% drop in speed, then return to original speed.
Setting Monitor Alarm Auger Speed:
Highlight the auger channel press and hold the set button. Four Digits will appear in the display. Continue to hold the set button, the 1st digit on the left will flash, continue to hold set and eventually it will switch to the next button, once that happens press the arrow button till the 1 digit appears. Eventually the next button will flash and move it to 5. Then make the last one 0, release the set button and continue with harvesting operations.
Monitor Reading Zero when Header is Engaged:
Swap monitor leads from Rotor and Auger. (Pin #6 & #3)
If no readings develop from this, check wires for damage.
No damage wires swap senders from auger and rotor to isolate the problem.
Re-setting the monitor.
CX/Early VS Monitor Heads:
With the power off press and hold the set, toggle button and the 'hidden button' found in the 'our' of Shelbourne. Hold these three buttons in, switch the power on and once it flashes power on the display release the buttons. Run up the machine and if no readings appear try resetting the monitor again.
Later VS Monitor Heads:
With the power off press and hold the middle three buttons then power up, release the buttons. Run up the machine and if no readings appear, try resetting the monitor again.
5-Speed Header set-up guide
|
CX-RX 6.0 8.4 |
Select Gear Input Shaft |
Select Gear Intermediate |
Auger Drive Sprocket |
Auger Finger Quantity |
PTO Yoke |
|
Case IH 16/21/23 |
29 Teeth (191804 29) |
27 Teeth (191804 27) |
18 Teeth - 3/4"pt (192768 18) |
16 (192310 02) |
Hexagon PTO00070 |
| John Deere 9600 9610 8820 |
29 Teeth (191804 29) |
27 Teeth (191804 27) |
18 Teeth - 3/4"pt (192768 18) |
24 (192310 02) |
Hexagon PTO00070 |
|
John Deere 9500 7720 CTS |
29 Teeth (191804 29) |
27 Teeth (191804 27) |
18 Teeth - 3/4"pt (192768 18) |
20 (192310 02) |
Hexagon PTO00070 |
|
John Deere STS |
29 Teeth (191804 29) |
27 Teeth (191804 27) |
18 Teeth - 3/4"pt (192768 18) |
20 (192310 02) |
21 Spline PTO00082 |
|
New Holland TR Models |
27 Teeth (191804 27) |
29 Teeth (191804 29) |
16 Teeth - 3/4"pt (192768 04) |
16 (192310 02) |
6 Spline PTO00080 |
|
New Holland TX66 |
31 Teeth (191804 31) |
25 Teeth (191804 25) |
22 Teeth - 3/4"pt (192768 10) |
24 (192310 02) |
6 Spline PTO00080 |
|
Gleaner R-Series |
27 Teeth (191804 27) |
29 Teeth (191804 29) |
15 Teeth - 3/4"pt (192768 16) |
16 (192310 02) |
21 Spline PTO00082 |
|
CAT 480 485 |
24 Teeth (191804 24) |
32 Teeth (191804 32) |
13 Teeth - 3/4"pt (192768 08) |
24 (182310 02) |
21 Spline PTO00082 |
|
CAT 460 465 |
24 Teeth (191804 24) |
32 Teeth (191804 32) |
16 Teeth - 3/4"pt (192768 04) |
24 (192310 02) |
21 Spline PTO00082 |
5-Speed Gear Ratios
|
Driven LH |
Driven RH |
Rotor Speed RPM approx |
|
20 |
26 |
850 |
|
22 |
24 |
710 |
|
24 |
22 |
600 |
|
26 |
20 |
500 |
|
28 |
18 |
420 |
When changing gears it is important to make sure that the header is lowered to the ground or oil will spill out of the box. Remove the thumb screws in the back of the gearbox & pull the cover off. Select the correct gears for the required speed. Check oil level. The spare gears must be replaced onto the back of the gearbox cover to keep the driving gears in place. Replace the gearbox cover & hand tighten the thumb screws.
RSD Pulley Speed Chart
|
Rotor Speed |
Rotor Pulley |
Input Pulley |
Gearbox Position |
|
460rpm |
14 1/2" |
11" |
3 |
|
550rpm |
14 1/2" |
13 1/4" |
1 |
|
660rpm |
13 1/4" |
14 1/2" |
1 |
|
790rpm |
11" |
14 1/2" |
3 |
Header Offset to Right
|
Header Size |
Offset (mm) |
Offset (in) |
|
32ft |
400 |
15 3/4 |
|
28ft |
300 |
11 13/16 |
|
24ft |
200 |
7 7/8 |
|
<24ft |
0 |
0 |
How to Calculate Acreage:
Length (ft) x Width (ft) / 43,560 = Acres
|
Width (feet) |
1/4 Mile |
1/2 Mile |
1 Mile |
|
22' |
0.65 acres |
1.31 acres |
2.62 acres |
|
24' |
0.71 acres |
1.43 acres |
2.86 acres |
|
28' |
0.83 acres |
1.67 acres |
3.34 acres |
|
32' |
0.95 acres |
1.91 acres |
3.82 acres |
